Putting in a tin roof over current shingles will be an effective way to present your property a brand new look and shield it from the weather. Nevertheless, it is essential to do the job accurately to keep away from any issues down the street. On this article, we’ll stroll you thru the steps on the way to put a tin roof over shingles, together with the way to put together the roof, set up the tin panels, and end the job. By following these directions, you possibly can be sure that your new tin roof will final for a few years to return.
Earlier than you start, it is essential to ensure that your roof is in good situation. If there are any broken or lacking shingles, you will have to restore them earlier than you possibly can set up the tin roof. As soon as the roof is in good situation, you can begin by eradicating any previous flashing or different roofing supplies that could be in the best way. Then, you will want to put in a layer of roofing felt over the shingles. This can assist to guard the shingles from the weather and supply a easy floor for the tin panels.
As soon as the roofing felt is in place, you can begin putting in the tin panels. Tin panels are usually connected to the roof utilizing screws or nails. It is essential to make use of the proper kind and measurement of fasteners for the kind of tin panels you are utilizing. As soon as the tin panels are put in, you will have to seal the seams between the panels utilizing a roofing sealant. This can assist to stop water from leaking into the roof. Lastly, you possibly can set up any mandatory trim or flashing to complete the job.
Assessing the Situation of Current Shingles
Earlier than putting in a metallic roof over shingles, it is essential to completely consider the situation of the prevailing shingles to make sure a profitable and long-lasting set up. Listed below are some key components to think about:
Age and Situation of Shingles
Examine the shingles for indicators of damage and tear which will have an effect on the soundness of the brand new metallic roof. Search for:
– Curled, cracked, or lacking shingles
– Granules loss, leading to uncovered asphalt
– Rot or water injury
– Free or lacking nails
– Sagging or uneven roof areas
Roofing Underlayment
Look at the situation of the roofing underlayment, which acts as a moisture barrier between the shingles and the roof deck. Verify for:
– Rips, tears, or holes
– Deterioration or crumbling
– Correct set up and overlap
Slope and Floor
Assess the slope and floor of the roof. A metallic roof requires a minimal slope for correct drainage. Verify for:
– Flat or low-slope areas which will retain water
– Uneven surfaces or protrusions
– Valleys, hips, and ridges which will require particular consideration
Flashing
Examine the flashing round chimneys, vents, and different roof penetrations. Be certain that the flashing is:
– Safe and watertight
– Effectively-sealed to stop leaks
– Fabricated from a sturdy materials
By fastidiously assessing these components, owners could make knowledgeable choices about whether or not their current shingles can help a metallic roof set up. If any vital points are recognized, it could be essential to restore or exchange the shingles earlier than continuing with the metallic roof set up.
Making ready the Roof Floor for Tin Set up
Earlier than you possibly can set up a tin roof over shingles, you’ll want to put together the roof floor. This entails eradicating any current shingles, in addition to any nails or staples that could be holding them in place. As soon as the roof is evident, you’ll want to examine it for any injury. When you discover any broken areas, you will have to restore them earlier than you possibly can set up the tin roof.
Inspecting the Roof
After you have eliminated the shingles, you’ll want to examine the roof for any injury. This contains in search of any holes, cracks, or lacking shingles. You must also test the flashing across the chimneys and vents to ensure that it’s in good situation. When you discover any injury, you will have to restore it earlier than you possibly can set up the tin roof.
Here’s a desk of among the most typical kinds of roof injury and the way to restore them:
| Kind of Injury | Easy methods to Restore |
|---|---|
| Holes | Patch the holes with roofing cement or flashing. |
| Cracks | Seal the cracks with roofing cement or caulk. |
| Lacking shingles | Exchange the lacking shingles with new ones. |
| Broken flashing | Exchange the broken flashing with new flashing. |
Choosing the Applicable Gauge and Kind of Tin
Selecting the best gauge and kind of tin is essential for a sturdy and aesthetically pleasing tin roof.
Gauge
Tin roofing is offered in varied gauges, which discuss with its thickness. Thicker tin is extra sturdy however heavier and dearer. For residential purposes, 26- or 28-gauge tin is often beneficial. This is a desk summarizing the variations:
| Gauge | Thickness (Inches) | Weight (Kilos per Sq. Foot) |
|---|---|---|
| 24 | 0.024 | 1.25 |
| 26 | 0.018 | 0.90 |
| 28 | 0.015 | 0.75 |
Kind
There are two predominant kinds of tin roofing: terne-coated metal and aluminum-zinc alloy. Every has its personal benefits and downsides:
- Terne-coated metal is a conventional materials that has been used for hundreds of years. It is constructed from metal that is coated with a skinny layer of tin. Terne-coated metal is sturdy, corrosion-resistant, and comparatively cheap. Nevertheless, it may be noisy when raining and may develop rust spots over time.
- Aluminum-zinc alloy is a more recent materials that is constructed from an alloy of aluminum and zinc. It is lighter than terne-coated metal, extra corrosion-resistant, and does not make as a lot noise when raining. Nevertheless, it is dearer and will be tougher to put in.
Elements to Take into account
When selecting the gauge and kind of tin, think about the next components:
- Local weather: In areas with extreme climate situations, a thicker gauge tin could also be mandatory.
- Funds: Terne-coated metal is mostly extra reasonably priced than aluminum-zinc alloy.
- Aesthetics: Terne-coated metal has a extra conventional look, whereas aluminum-zinc alloy has a extra trendy look.
Slicing and Shaping the Tin Panels
As soon as you’ve got measured and marked the tin panels, you will want to chop them to measurement. Use tin snips or a round noticed with a metallic reducing blade to make clear, straight cuts. When reducing, you’ll want to put on security glasses and gloves to guard your self from sharp edges.
After reducing the panels, you might have to form them to suit round obstacles, equivalent to chimneys or skylights. To do that, use a tin brake or a pair of pliers to bend the panels into the specified form. Watch out to not over-bend the panels, as this could weaken the metallic.
As soon as the panels are lower and formed, you are prepared to put in them on the roof. Begin by nailing the underside fringe of the primary panel to the roof deck. Then, overlap the following panel over the primary panel by 2 inches and nail it down. Proceed on this method, overlapping every panel by 2 inches till you attain the highest of the roof.
As you are putting in the panels, you’ll want to seal the seams with roofing cement to stop leaks. You may also use a ridge cap to cowl the seam on the peak of the roof.
Suggestions for Slicing and Shaping Tin Panels
- Use sharp tin snips or a round noticed with a metallic reducing blade.
- Put on security glasses and gloves to guard your self from sharp edges.
- Watch out to not over-bend the panels, as this could weaken the metallic.
- Begin by nailing the underside fringe of the primary panel to the roof deck.
- Overlap the following panel over the primary panel by 2 inches and nail it down.
- Proceed on this method, overlapping every panel by 2 inches till you attain the highest of the roof.
- Seal the seams with roofing cement to stop leaks.
- Use a ridge cap to cowl the seam on the peak of the roof.
Putting in the Tin Panels: Beginning on the Backside
1. Begin on the Edge
Start by aligning the primary tin panel on the backside fringe of the roof, making certain it overhangs the sting by roughly 2 inches. Use roofing nails to safe it each 12 inches alongside the underside edge.
2. Set up Starter Strips
Set up starter strips alongside the underside fringe of the roof, which can assist hold the tin panels in place. Nail the starter strips into the roof deck utilizing roofing nails spaced 6 inches aside.
3. Overlap the Panels
Overlap the following tin panel by a minimal of 6 inches, making certain the overlapped part is towards the prevailing wind course. Drive roofing nails by means of the overlapped part, spacing them 12 inches aside.
4. Set up Aspect Laps
Set up facet laps by fastening tin panels along with roofing nails. Overlap the panels vertically by 4 inches and nail them collectively each 12 inches, making a weathertight seal.
5. Seal the Joints
To forestall water infiltration, seal all joints and seams utilizing a high-quality roofing sealant. Apply a beneficiant bead of sealant alongside the sides and overlaps, then easy it out with a putty knife. Enable the sealant to dry utterly earlier than transferring on.
| Joint Kind | Sealing Methodology |
|---|---|
| Horizontal Overlaps | Apply sealant alongside the overlapped part |
| Vertical Aspect Laps | Seal between the panels and the facet laps |
| Roof Edges | Caulk across the edges of the tin roofing |
Overlapping and Sealing the Tin Panels
Correctly overlapping and sealing the tin panels is important for making certain a leak-proof and sturdy roof. Observe these steps fastidiously:
1. Overlapping the Panels
- Begin on the backside fringe of the roof and work your means up.
- Overlap every row of panels by a minimum of 6 inches.
- Be certain that the horizontal seams overlap vertically by a minimum of 12 inches.
2. Putting in the Middle Seam
Use tin snips to chop a V-shape into the middle of the overlapping panels. This creates a channel for the sealant to movement into.
3. Making use of Sealant
Apply a beneficiant bead of roofing sealant into the V-shaped channel. Use a caulking gun for exact software.
4. Crimping the Seam
Use a seaming software to crimp the sides of the overlapping panels collectively. This can assist seal the seam and stop leaks.
5. Making use of Silicone Caulk
Apply a bead of silicone caulk alongside the whole size of the crimped seam. This can present a further layer of safety towards moisture penetration.
6. Flashing the Seams
To make sure most safety, set up a layer of flashing over the crimped and sealed seams. The flashing ought to be fabricated from a water-resistant materials equivalent to galvanized metal or aluminum and will overlap the seams by a minimum of 6 inches on all sides.
| Flashing Materials | Advisable Overlap |
|---|---|
| Galvanized Metal | 6 inches |
| Aluminum | 6 inches |
Flashing and Trim Work
Flashing
Flashing refers to skinny sheets of metallic used to seal the roof’s edges, stopping water from penetrating. It is usually fabricated from galvanized metal, aluminum, or copper and is available in varied sizes and shapes to suit completely different roof parts.
Step 1: Set up Base Flashing
Safe the bottom flashing to the roof’s edge, the place the shingles meet the fascia boards. Overlap the flashing on the corners and seal it with caulk.
Step 2: Set up Step Flashing
Lower step flashing into items that match the spacing between the shingles. Slide the flashing beneath the shingles and over the bottom flashing. Seal the joints with caulk.
Step 3: Set up Ridge Cap Flashing
Match the ridge cap flashing over the ridge of the roof. Overlap the panels and seal them with adhesive.
Step 4: Create Customized Flashing
In some instances, you might have to create customized flashing items for complicated rooflines or penetrations. Use a metallic brake or snips to chop the flashing to the specified form.
Trim Work
Trim work refers to ornamental components used to boost the roof’s look and shield its edges from injury.
Step 1: Set up Facia Boards
The fascia boards are put in across the roof’s perimeter, masking the sides of the roof sheathing and shingles.
Step 2: Set up Soffit Vents
Soffit vents are put in on the underside of the eaves to permit air to flow into by means of the roof’s attic area.
Step 3: Add Exterior Nook Trim
Exterior nook trim is put in on the corners of the roof to supply further safety and a seamless look.
Step 4: Select Ornamental Trim
Numerous ornamental trim choices can be found, equivalent to molding, gingerbread, and finials. These components can improve the roof’s aesthetic enchantment.
Portray or Coating the Tin Roof
Portray or coating your tin roof can improve its longevity, shield it from the weather, and enhance its aesthetic enchantment. Listed below are some detailed steps to comply with:
1. Cleansing the Roof
Totally clear the roof to take away grime, particles, and any current paint or coating. Use a stress washer or a stiff brush with a cleansing resolution.
2. Preparation
Examine the roof for any injury or rust spots. Restore any damages and sand down any rust spots.
3. Primer Utility
Apply a metal-specific primer to the roof. This can present an excellent base for the paint or coating to stick to.
4. Paint or Coating Choice
Select a paint or coating designed particularly for metallic roofs. Take into account components equivalent to rust resistance, UV safety, and colour.
5. Utility Strategies
Use a brush or curler to use the paint or coating. Apply even coats and keep away from leaving any streaks or drips.
6. Drying Time
Enable the paint or coating to dry in response to the producer’s directions. Drying instances could differ relying on the product and climate situations.
7. A number of Coats
For optimum safety and sturdiness, apply a number of coats of paint or coating. Sand calmly between coats to make sure a easy end.
8. Security Precautions
Put on acceptable security gear, together with gloves, eye safety, and a mud masks, when dealing with the paint or coating. Guarantee enough air flow when working with solvent-based merchandise.
| Gutter Materials | Professionals | Cons |
|---|---|---|
| Copper | Sturdy, corrosion-resistant, aesthetically pleasing | Costly, requires soldering |
| Metal | Sturdy, reasonably priced, simple to put in | Can rust if not correctly protected |
| Aluminum | Light-weight, corrosion-resistant, simple to form | Might be dearer than metal |
Sustaining and Repairing the Tin Roof
Common upkeep is essential to increase the lifespan of a tin roof. Listed below are some important steps to maintain it in good situation:
- Clear the Roof: Take away particles, grime, and mould by gently washing the roof with a gentle detergent and comfortable brush.
- Examine the Roof: Repeatedly test for any injury, equivalent to leaks, unfastened sheets, or rust spots.
- Restore Leaks: If leaks are detected, find the supply and use sealant or patching supplies to restore them promptly.
- Exchange Broken Sheets: If sheets are broken past restore, they need to get replaced with new ones.
- Contact Up Paint: Contact up any scratched or peeling paint to stop rust and corrosion.
- Examine and Clear Gutters: Ensure gutters are freed from particles and functioning correctly to stop water injury.
- Trim Overhanging Bushes: Take away branches which will injury the roof throughout storms or excessive winds.
- Stroll with Warning: Keep away from strolling on the roof except mandatory, as extreme foot site visitors may cause injury.
- Keep away from Acidic Cleaners: Use gentle cleansing brokers to keep away from damaging the protecting coating on the tin.
- Annual Inspection: Schedule an annual inspection by a roofing skilled to evaluate the roof’s situation and determine any potential points.
| Upkeep Frequency | Job |
|---|---|
| Month-to-month | Clear roof and examine for leaks |
| Yearly | Restore leaks, exchange broken sheets, and contact up paint |
| Yearly | Skilled roof inspection |
Security Precautions for Tin Roof Set up
Putting in a tin roof over shingles requires cautious preparation and adherence to security pointers. To make sure a profitable and hazard-free set up, comply with these complete security precautions:
-
Set up Security Tools:
Put on acceptable security gear, together with a tough hat, security glasses, gloves, and durable work boots, to guard towards falling particles and sharp edges.
-
Examine the Roof:
Earlier than starting set up, completely examine the roof for any structural injury, unfastened shingles, or potential hazards.
-
Safe the Ladder:
Use a sturdy extension ladder with a large base and tie it off securely to stop slipping or falling.
-
Use Fall Safety:
Set up fall safety gear, equivalent to a security harness or a roof anchor level, if working at heights.
-
Keep away from Energy Strains:
Keep a protected distance from energy traces and keep away from any contact with them.
-
Verify Climate Situations:
Plan set up throughout favorable climate situations, avoiding excessive warmth, rain, or sturdy winds.
-
Put on Protecting Clothes:
Put on lengthy sleeves and pants to guard your pores and skin from metallic shavings and sharp edges.
-
Deal with Supplies Safely:
Use correct lifting strategies to maneuver tin roof panels and different heavy supplies to stop accidents.
-
Safe Instruments and Tools:
Maintain all instruments and gear in a chosen space to stop them from falling or being knocked over.
-
Observe Producer Directions:
Rigorously learn and comply with the producer’s set up directions for the tin roof and any related supplies.
Easy methods to Put a Tin Roof Over Shingles
Putting in a tin roof over shingles is an effective way to increase the lifetime of your roof and add a trendy contact to your property. Nevertheless, it is essential to notice that this can be a complicated venture that ought to solely be undertaken by skilled roofers. Listed below are some easy steps to comply with:
- Take away the prevailing shingles.
- Set up a layer of roofing felt over the naked roof deck.
- Set up the metallic panels over the roofing felt, ranging from the underside fringe of the roof and dealing your means up.
- Safe the metallic panels with roofing screws.
- Set up flashing across the edges of the roof and any penetrations, equivalent to chimneys or skylights.
- Trim the surplus metallic and caulk across the edges of the roof.
Folks Additionally Ask About Easy methods to Put a Tin Roof Over Shingles
Do I have to take away the prevailing shingles earlier than putting in a tin roof?
Sure, you will need to take away the prevailing shingles earlier than putting in a tin roof. This can be sure that the brand new roof is correctly put in and won’t be broken by the previous shingles.
Can I set up a tin roof over broken shingles?
No, you shouldn’t set up a tin roof over broken shingles. The broken shingles might compromise the integrity of the brand new roof and result in leaks.
How lengthy will a tin roof final?
A tin roof can final for 50 years or extra with correct upkeep.
