Are you feeling overwhelmed by the considered eradicating your overhead microwave? Don’t fret, it isn’t as daunting as it might appear. With slightly preparation and the appropriate instruments, you may simply take away your overhead microwave and release some much-needed area in your kitchen. On this complete information, we’ll stroll you thru each step of the method. Whether or not you are a seasoned DIYer or a kitchen novice, this information will empower you to deal with this job with confidence.
Earlier than you start, collect the mandatory instruments and supplies. You’ll need a step ladder, a screwdriver, a pair of pliers, and presumably a wire cutter. It is also a good suggestion to have a helper readily available to help you with lifting and stabilizing the microwave. After you have the whole lot you want, begin by disconnecting the facility to the microwave on the circuit breaker. Subsequent, take away the screws that safe the mounting bracket to the cupboard. As soon as the mounting bracket is free, fastidiously raise the microwave out of the cupboard. Disconnect {the electrical} wires from the microwave and decrease it to the ground. Lastly, eliminate the microwave in line with native laws.
Eradicating an overhead microwave could be a rewarding expertise, particularly in the event you’re trying to improve or rearrange your kitchen. By following these steps, you may safely and successfully take away your microwave with out damaging it or your kitchen. Nonetheless, it is necessary to do not forget that in the event you’re not comfy performing electrical work, it is best to seek the advice of a professional electrician. With slightly effort and the appropriate method, you may release priceless area in your kitchen and benefit from the satisfaction of a job effectively completed.
Eradicating the Higher Screws
Now that the microwave is supported, you may start eradicating the higher screws. These screws are sometimes positioned on the highest of the microwave, close to the again. They might be coated by a plastic panel, which you’ll need to take away first utilizing a screwdriver.
After you have positioned the higher screws, use a screwdriver to take away them. Watch out to not drop the screws, as they are often tough to search out in the event that they fall into the microwave.
As soon as the entire higher screws have been eliminated, you may fastidiously raise the microwave off of the mounting bracket. You’ll want to maintain the microwave securely, as it may be heavy.
Ideas for Eradicating the Higher Screws
Listed here are some ideas for eradicating the higher screws:
- Use a screwdriver that’s the appropriate measurement for the screws. A screwdriver that’s too small will strip the screws, whereas a screwdriver that’s too giant will harm the microwave.
- Watch out to not overtighten the screws. Overtightening the screws can harm the microwave.
- In case you are having problem eradicating a screw, strive utilizing a penetrating oil. Penetrating oil may also help to loosen the screw in order that it may be eliminated extra simply.
Troubleshooting
In case you are having problem eradicating the higher screws, it’s doable that they’re rusted or broken. On this case, you could want to make use of a drill to take away the screws. Listed here are some ideas for utilizing a drill to take away screws:
- Use a drill bit that’s the identical measurement because the screws.
- Drill a pilot gap into the middle of the screw.
- Use a screwdriver to take away the screw.
Disconnecting the Wiring
After you have eliminated the duvet and accessed the wiring, proceed with the next steps to soundly disconnect the microwave:
1. Flip off the Electrical energy
Find the circuit breaker or fuse field that controls the electrical energy to the microwave and change it off. This step is essential for security earlier than dealing with any electrical parts.
2. Take away the Screws
Utilizing a screwdriver, take away the screws that safe {the electrical} wires to the terminals on the microwave. Sometimes, these screws are positioned on the again or backside of the unit.
3. Disconnect the Wires
Rigorously pull {the electrical} wires away from the terminals. To keep away from damaging the wires or terminals, use needle-nose pliers or insulated wire strippers to softly disconnect them.
4. Mark the Wires
To make sure correct reconnection later, mark or label the wires with tape or a marker. This step will provide help to establish the corresponding wires when reattaching the microwave.
5. Wrap the Wires
For security and to forestall quick circuits, wrap the uncovered wires with electrical tape. This may insulate the wires and scale back the danger of unintentional contact throughout the elimination and reinstallation course of. Here is a desk summarizing the wire-wrapping course of:
| Function | Steps |
|---|---|
| Insulating uncovered wires | Wrap every wire individually with electrical tape. |
| Securing the tape | As soon as wrapped, safe the tape by overlapping it a number of instances. |
| Stopping quick circuits | Be sure that the tape absolutely covers the uncovered wires with none frayed or broken spots. |
Eradicating the Microwave from the Wall
1. Disconnecting the Energy
Unplug the microwave from the facility outlet. In case your microwave is hardwired, flip off the breaker or fuse that provides energy to the microwave.
2. Eradicating the Mounting Bracket
Find the mounting bracket that holds the microwave to the wall. Take away the screws that safe the bracket to the wall and to the microwave.
3. Lifting the Microwave from the Bracket
Grip the microwave firmly from each side and raise it straight as much as take away it from the mounting bracket.
4. Eradicating the Screws from the Again of the Microwave
As soon as the microwave is free from the bracket, take away the screws from the again of the microwave that safe it to the wall. There needs to be two screws on the prime and two on the backside.
5. Pulling the Microwave Ahead
Grip the microwave firmly and pull it straight towards you to take away it from the wall.
6. Eradicating the Energy Twine and Wiring
As soon as the microwave is obvious of the wall, take away the facility twine and some other wiring that’s hooked up to it.
7. Eradicating the Assist Brackets (if obligatory)
In case your microwave was put in with help brackets that stretch from the underside of the microwave to the ground, you’ll need to take away these brackets. There could also be screws or bolts that safe the brackets to the microwave and to the ground. Take away these fasteners and thoroughly raise the microwave off of the brackets.
Patching the Gap
As soon as the microwave is eliminated, you will be left with a gap in your cupboard. There are a number of alternative ways to patch this gap, relying on the scale and site. For small holes, you may merely fill them in with spackling paste or wooden filler. For bigger holes, you could want to chop a chunk of plywood to suit the opening after which connect it with screws or nails. As soon as the opening is patched, you may paint or stain it to match the remainder of the cupboard.
Listed here are the steps on easy methods to patch a gap in your cupboard:
- Clear the world across the gap with a humid fabric.
- If the opening is small, fill it in with spackling paste or wooden filler utilizing a putty knife.
- If the opening is giant, reduce a chunk of plywood to suit the opening.
- Connect the plywood to the cupboard with screws or nails.
- Fill in any gaps across the plywood with spackling paste or wooden filler.
- Sand the patched space till it’s clean.
- Paint or stain the patched space to match the remainder of the cupboard.
| Materials | Instruments |
|---|---|
| Spackling paste or wooden filler | Putty knife |
| Plywood (if the opening is giant) | Screws or nails |
| Sandpaper | Paint or stain |
Disconnecting Energy
1. Shut off the microwave’s circuit breaker or fuse at your own home’s electrical panel.
2. Unplug the microwave from {the electrical} outlet.
Eradicating Gasoline Line
3. Shut off the gasoline valve that provides the microwave.
4. Disconnect the gasoline line from the microwave.
Eradicating Mounting Brackets
5. Find the mounting brackets that safe the microwave to the wall or cupboard.
6. Take away the screws or bolts that maintain the brackets in place.
Reducing the Microwave
7. Have a helper help the microwave as you fastidiously take away it from the mounting brackets.
8. Raise the microwave down and place it on a sturdy floor.
Restoring Energy and Gasoline
Restoring Energy
9. Earlier than turning on the circuit breaker or fuse, fastidiously examine all wires and connections.
10. If the whole lot appears safe, activate the circuit breaker or fuse and plug within the microwave.
Restoring Gasoline
11. Verify for any leaks within the gasoline line by making use of a soapy water resolution to all joints.
12. If no bubbles seem, activate the gasoline valve and relight the microwave’s pilot gentle.
| Kind of Circuit Safety | Location |
|---|---|
| Circuit Breaker | Electrical Panel |
| Fuse | Fuse Field |
Learn how to Take away an Overhead Microwave
Eradicating an overhead microwave could be a daunting job, however it’s doable to do it your self with the appropriate instruments and security precautions. Listed here are the steps on easy methods to take away an overhead microwave:
- Flip off the facility to the microwave. This may be completed on the circuit breaker or fuse field.
- Disconnect the microwave from {the electrical} outlet.
- Take away the mounting bolts. There are sometimes 4 bolts that maintain the microwave in place. Use a socket wrench to take away the bolts.
- Decrease the microwave barely. Have somebody provide help to decrease the microwave slowly so to disconnect the exhaust duct.
- Disconnect the exhaust duct. The exhaust duct is often held in place by a clamp. Use a screwdriver to loosen the clamp and disconnect the duct.
- Take away the microwave. Rigorously raise the microwave off of the mounting brackets and take away it from the kitchen.
Folks Additionally Ask
How do I do know if my microwave is overhead?
Overhead microwaves are sometimes put in above the range or vary. They’re often mounted to the wall or ceiling.
What instruments do I have to take away an overhead microwave?
You’ll need the next instruments to take away an overhead microwave:
- Socket wrench
- Screwdriver
- Step ladder
- Helper (optionally available)
Can I take away an overhead microwave myself?
Sure, it’s doable to take away an overhead microwave your self with the appropriate instruments and security precautions. Nonetheless, it is very important word that microwaves will be heavy and awkward to deal with. In case you are not comfy eradicating the microwave your self, it’s best to rent a professional equipment restore technician.
